Walker T25i User Manual download pdf (Page 6)

ITEM PART DESCRIPTION NO.

NO. NO. REQ’D

ITEM PART DESCRIPTION NO.

NO. NO. REQ’D

4

Beginning S/N 125598

Effective Date 11-18-13

Use only genuine Walker

®

replacement parts.

BODY / CHASSIS ASSEMBLY (GHS MODELS)

Seat Assembly

1 5103 Seat 1

2 7203 Seat Spring Plate 1

3 7223-1 Compression Spring 2

4 7845-1 Rubber Bumper (1.375 x .750) 2

5 7846 Washer (3/8 ID x 1-1/4 OD x 1/8) 2

6 5841-1 Retainer Washer 2

7 7440-5 Shock Mount (1-1/4 x 3/4) 2

Rear Bumper Assembly (GHS Models Only)*

8 7516 GHS Rear Bumper 1

9 7516-5 Catcher Pivot Bushing 2

10 5162 Roller Wheel (5" Rubber) 2

11 7517-2 Catcher Pivot Plate 2

Body Assembly

12 NS Body ID Plate 1

13 5989-12 Dome Plug (3/16) 1

14 5989-10 Dome Plug (9/16) 1

15 5845 Rubber Bumper (1.50 OD x 1.25) 4

16 8118 HeatDeector 1

17 7422 Panel Guard 1

18 5989-4 Dome Plug (3/8) 4

19 5989-3 Dome Plug (5/16) 2

20 5146 10mm Ball Stud 2

21 7844 Rubber Bumper (1.25 OD x .250) 1

22 2145 Gas Spring 1

23 7222 Extension Spring (1/4 x 3) 1

24 7383-3 Body Latch Hook (2-1/2 Side Bars) 1

25 7854 Plastic Tip, Red 1

26 5989-9 Dome Plug (1/4) 8

27 8100-5 Front Body 1

28 5180 Edge Molding, Lever Opening 2

29 5989-55 Dome Plug (1/2) 1

30 5989-5 Dome Plug (7/16) 1

Tilt-Up Latch Assembly

***

31 5847 Plastic Tip 1

32 5744-20 Spring Arm, Tilt-Up Latch 1

33 5744-10 Spring Pivot Bushing 1

34 5744-15 Compression Spring (3/8 x 5/8) 1

35 5744-13 Mount Angle, LH 1

36 5744-12 Hook, Tilt-Up Latch 1

37 5744-14 Mount Angle, RH 1

Chassis Assembly

38 5267-1 Retainer Collar (1") (Includes Item # F413) 1

39 5270-1 Pivot Bearing 2

40 5842-1 Washer (1.0 ID x 1.350 OD) 1

41 7420 Tail Wheel Fork 1

42 5830-3 Grease Fitting (45 Degree) 2

43 8039 Nut, Tail Wheel Axle 2

44 8037-1 Seal, Outer (1-3/4 x 1-1/8) 2

45 8038-1 Spacer, Tail Wheel Axle 2

(.750 x ID x 1.125 OD)

46 8037 Bearing Cone (3/4 ID) 4

47 8035 Tail Wheel & Tire Assembly (13 x 5.00-6) 2

(With Bearing Race)

7035-1 Tail Wheel Tire (13 x 5.00-6)

**

8036 Wheel & Hub (6 x 3.25) **

(Includes Items # 42 & Bearing Race)

8037-2 Bearing Race **

48 8768-2 Seal, Reverse Lip 2

49 8038 Tail Wheel Axle (3/4 x 10-3/8) 1

50 7070 Wheel & Tire Assembly (18 x 9.50-8) 2

7070-1 Drive Tire (18 x 9.50-8) **

5070-4 Wide Wheel (8 x 7) **

51 8300-16 Chassis Frame (EFI / 5.0 gal.) 1

Fasteners

F002 10-24 Keps Nut 2

F004 1/4-20 Keps Nut 2

F005 1/4-20 ESNA Nut 1

F009 5/16-18 Whiz Locknut 12

F012 3/8-16 Keps Nut 8

F013 3/8-16 Whiz Locknut 2

F014 3/8-16 ESNA Nut 4

F020 5/16-18 ESNA Nut 1

F025 10-24 x 3/8 PPHMS 2

F029 1/4-20 x 1/2 Hex Bolt 2

F031 1/4-20 x 5/8 Hex Bolt 1

F034 5/16-18 x 3/4 Hex Bolt 2

F038 3/8-16 x 1 Hex Bolt 6

F040 3/8-16 x 1-1/2 Hex Bolt 2

F042 3/8-16 x 2-1/4 Hex Bolt 2

F050 1/4 SAE Washer 1

F051 3/8 SAE Washer 2

F059 3/8 Wave Spring Washer 2

F093 5/16-18 x 1 Hex Bolt 1

F151 3/8-16 x 7/8 Hex Bolt 2

F157 1/2-20 x 1-1/4 Wheel Lug Bolt 8

F205 5/16-18 x 1/4 Set Screw, Knurl Point 2

F206 #2 x 3/16 Drive Pin 2

F218 7/16 Split Lock Washer 2

F219 7/16-14 x 1-1/4 Hex Bolt 2

F227 3/8 x 1-1/4 x 1/8 Plastic Washer 2

F241 .375 x .875 x .10 Washer 4

F257 3/8 x 1-11/16 Shoulder Bolt 2

F341 Coil Roll Pin (7/64 x 9/16) 1

F342 5/16 Conical Washer 2

F413 5/16-24 x 5/16 Set Screw 2

* Rear Bumper Assembly for SD Models is not shown here.

Refer to BODY ASSEMBLY (SD MODELS), Page 8.

** Service Part Only

*** Complete Tilt-Up Latch Assembly Kit available by ordering

kit # 5747.

1 2 3 4 5 6 7 8 9 10 11 ... 47 48

Comments to this Manuals

No comments